DIY REPAIR GUIDE — HYUNDAI ELANTRA, SONATA, SANTA FE, TUCSON, ACCENT, VERACRUZ, GENESIS C
Hyundai & Kia Brake Light Switch Failure & Replacement
A failing brake light switch is a well-known Hyundai and Kia problem.
321 Rexdale Blvd #4, Etobicoke, ON M9W 1R8
Mon–Fri 8am–5pm · (416) 742-4521
⚡ Servicing your car at an independent shop does not void your vehicle warranty — protected under Canadian consumer protection law.
By the Radman Auto Repair team, independent auto repair in Etobicoke since 1999 · Updated November 2026
A failing brake light switch is a well-known Hyundai and Kia problem. The plastic stopper pad on the brake pedal crumbles, so the switch can’t tell when you brake. The brake lights stay on or don’t work, the ESC light comes on, and the car may not shift out of Park.
Quick answer: If a Hyundai or Kia has brake lights that stay on or don’t work, an ESC or traction light, cruise that won’t engage or a shifter stuck in Park, check the brake light switch and the stopper pad under the dash. Many 2007–2011 models are covered by a recall; otherwise it’s a 15-minute DIY.
At a glance
- Vehicles: Hyundai Elantra, Sonata, Santa Fe, Tucson, Accent, Veracruz, Genesis Coupe 2007–2013; Kia Soul, Sorento, Sportage, Optima, Rondo, Sedona
- DIY difficulty: Easy
- Time: about 20 minutes
- Tools: flashlight, helper or a wall to see the brake lights, pliers, OBD2 scan tool (optional)
- Parts: brake light (stop lamp) switch, brake pedal stopper pad
- Codes & warning lights: ESC/VSC light, traction control light, ABS light, P0504 or C1513 brake switch codes
- Recalls: check your VIN first; some of these problems are covered by recalls, campaigns or extended warranties
Symptoms
Brake lights stay on the brake lights glow with your foot off the pedal, draining the battery.
No brake lights the lights don’t come on when you brake.
Stuck in Park the shifter won’t leave Park even with your foot on the brake.
Warning lights ESC, traction control or ABS lights come on.
Cruise won’t work cruise control won’t set or won’t cancel with the brake.
Push-start won’t crank the car won’t start because it doesn’t see the brake pedal.
What Causes It
Crumbled stopper pad the plastic pad between the pedal and the switch breaks down, leaving bits on the floor.
Worn switch the switch contacts fail.
Misadjusted switch a switch not set correctly against the pedal.
Before You Start
- Park on level ground, set the parking brake and chock the wheels. Never work under a car held up only by a jack: use rated jack stands.
- Let the engine and exhaust cool before you touch them; coolant systems are under pressure when hot.
- Wear safety glasses and gloves, and disconnect the 12V battery before unplugging electrical parts or working near airbags.
- Check for open recalls on your VIN (Transport Canada or the manufacturer’s site) before you buy parts: a recall repair is free at the dealer.
- Check the recall before buying parts: the dealer replaces the switch free on recalled vehicles.
Step-by-Step: Hyundai & Kia Brake Light Switch
- Check the brake lights. Have a helper watch, or back up to a wall at night, and press the brake.
- Check the recall. Enter your VIN at Transport Canada’s recall database or Hyundai or Kia Canada’s site.
- Look under the dash. Lie in the driver’s footwell and find the switch at the top of the brake pedal arm.
- Inspect the pad. Look for a missing or crumbled stopper pad and plastic bits on the floor.
- Remove the switch. Unplug the connector, then twist the switch a quarter turn and pull it out.
- Fit the new pad and switch. Install a new stopper pad, then insert the new switch with the pedal pulled up, and twist to lock it so it self-adjusts.
- Test. Check the brake lights, shifting out of Park and cruise. Clear any codes and confirm the ESC light is off.
When to Stop and Bring It In
- The brake lights still don’t work: check the bulbs, fuse and wiring.
- The ESC or ABS light stays on: the ABS module or a wheel speed sensor may also have a fault.
- The shifter still won’t leave Park: the shift interlock solenoid may be at fault.
- Your car is on the recall list: the dealer does it free.
Not sure, or out of time? Radman Auto Repair in Etobicoke does this repair every week. Book online or call (416) 742-4521.
Also Known As
Searched as “Hyundai brake lights stay on”, “Kia brake light switch recall”, “Elantra won’t shift out of park”, “Sonata ESC light”, “Soul brake light switch”, “Santa Fe stop lamp switch” and “Hyundai brake switch stopper pad”.
Frequently Asked Questions
Is the Hyundai and Kia brake light switch covered by a recall?
Many 2007–2011 Hyundai and Kia models were recalled in Canada and the US for this switch. Check your VIN; the dealer replaces it free if covered.
Why are my brake lights staying on?
The stopper pad between the pedal and switch has crumbled, so the switch thinks the pedal is always pressed.
Can a bad brake light switch stop the car from shifting?
Yes. The shift interlock needs a brake signal to release the shifter from Park.
Why does the ESC light come on with a bad brake switch?
The stability control uses the brake switch signal; when it’s wrong, the system shuts off and lights the warning.
Is it hard to replace?
No. It’s a twist-in switch at the top of the brake pedal and takes about 15 minutes.
See also Hyundai Repair & Service, Kia Repair & Service, Brakes & ABS Light, Dashboard Warning Lights Guide.






Prefer to Have It Done? Radman Auto Repair, Etobicoke
Independent auto repair in Etobicoke since 1999. We fix what this guide covers, explain what we find, and keep the old parts for you to see.
This Service Includes
✓ Brake light and switch check
✓ Stopper pad and switch replacement
✓ ESC and ABS code scan
✓ Recall check
